用水化资料对南黄海6.1级地震的预测

根据区域水氡平均年离散度变化及应用“地下流体预报方法ＳＨＥＰ软件”，对水化资料和一些Ｒｎ，Ｃｌ－，Ｃａ２＋单项异常进行综合分析，于１９９６年１０月提出：从１９９６年１０月下旬至１９９７年下半年，在南长带海域（尤其是东经１２１°±１°，北纬３３°±１°的区域）有发生Ｍｓ６．０级左右地震的可能，要特别注意１９９６年１０月下旬至１９９７年上半年（信度ＣＦ＝０．６）。本次南黄海６．１级地震映证了这一预报意见     

热辐射的破坏准则和池火灾的破坏半径

热辐射破坏是发生在开放气环境中的池火灾的主要破坏机理。本文讨论了热辐射的破坏准则，提出预测池火灾破坏半径的方法，进行了数值模拟计算，分而和时纳了池火灾的基本规律     

北京地区15000年以来环境变迁中灾害性气候突变事件的讨论

通过高分辨率孢粉分析及烧失量、炭屑实验结果的统计分析，结合１４Ｃ、古地磁等，对北京房山东甘池１５０００ａ以来植被变化和环境变迁进行了较为深入的研究，特别强调气候变化的灾害性突变事件。初步得知约在１４１００～１４０００ａＢ．Ｐ．前后曾出现与哥得堡反转相对应的事件，在１００００ａＢ．Ｐ．左右出现类似与新仙女木事件相对应的事件，在大约５７７０ａＢ．Ｐ．和４５６０ａＢ．Ｐ．左右及２８５０～２６５０ａＢ．Ｐ．出现了大暖期的突然降温事件。     

On the response of 500 gal propane tanks to a 25% engulfing fire

This paper presents detailed data on the thermal response of two 500 gal ASME code propane tanks that were 25% engulfed in a hydrocarbon fire. These tests were done as part of an overall test programme to study thermal protection systems for propane-filled railway tank-cars.

The fire was generated using an array of 25 liquid propane-fuelled burners. This provided a luminous fire that engulfed 25% of the tank surface on one side. The intent of these tests was to model a severe partially engulfing fire situation.

The paper presents data on the tank wall and lading temperatures and tank internal pressure. In the first test the wind reduced the fire heating and resulted in a late failure of the tank at 46 min. This tank failed catastrophically with a powerful boiling liquid expanding vapour explosion (BLEVE). In the other test, the fire heating was very severe and steady and this tank failed very quickly in 8 min as a finite rupture with massive two-phase jet release. The reasons for these different outcomes are discussed. The different failures provide a range of realistic outcomes for the subject tank and fire condition.     

On the thermal rupture of 1.9 m propane pressure vessels with defects in their thermal protection system

This paper describes the results from a series of fire tests that were carried out to measure the effect of defects in thermal protection systems on fire engulfed propane pressure vessels.

In North America thermal protection is used to protect dangerous goods rail tank-cars from accidental fire impingement. They are designed so that a tank-car will not rupture for 100 min in a defined engulfing fire, or 30 min in a defined torching fire. One common system includes a 13 mm blanket of high-temperature ceramic fibre thermal insulation covered with a 3 mm steel jacket. Recent inspections have shown that some tanks have significant defects in these thermal protection systems. This work was done to establish what levels of defect are acceptable from a safety standpoint.

The tests were conducted using 1890 l (500 US gallon) ASME code propane pressure vessels (commonly called tanks in the propane industry). The defects tested covered 8% and 15% of the tank surface. The tanks were 25% engulfed in a fire that simulated a hydrocarbon pool fire with an effective blackbody temperature of 870 °C.

The fire testing showed that even relatively small defects can result in tank rupture if the defect area is engulfed in a severe fire, and the defect area is not wetted by liquid from the inside. A wall failure prediction technique based on uniaxial high-temperature stress rupture test data has been developed and agrees well with the observed failure times.     

Study of lignocellulosic biomass ignition properties estimation from thermogravimetric analysis

In the last decade, the use of renewable resources has increased significantly in order to reduce the energetic dependence on fossil fuels, as they have an important contribution to the global warning and greenhouse gasses effect. Because of that, research on biofuels has been increased in the last years as its characteristics of use match those of the conventional fuel's: solid biomass can be used instead of coals, and biodiesel could replace diesel. Research on solid biomass ignition properties has been considerably developed because of the amount of industrial accidents related to the treatment and use of solid biomass (self-ignition, dust explosions, etc.). On the other hand, thermogravimetric analysis (TGA) is becoming and important characterization technique as it can be used to determine a wide spectrum of properties, such as kinetics, composition, proximate analysis, etc. This research aims to combine thermal analysis and ignition properties, by using the TGA to obtain the elemental composition of lignocellulosic biomass and compare those results to Minimum Ignition Energy (MIE) values test output, so a relation between composition and MIE can be found.To achieve this aim, biomass samples from different origins have been used: oil palm wastes (empty fruit bunches, mesocarp fiber and palm kernel shell), agricultural wastes (straw chops) and forestry wastes (wood chips and wood powder). Also, raw materials and torrefied biomass were compared. The hemicellulose/cellulose ratio was calculated and compared to different flammability properties, finding out that the greater the ratio and the lower the onset temperature (temperature at which the pyrolysis reaction accelerates), the lower was the minimum ignition energy. From this basis it was possible to define “tendency areas” that grouped the samples whose MIE values were similar. Three tendency areas were found: high minimum ignition energy, medium minimum ignition energy, and low ignition energy.     

Hazard evaluation for chlorination and amination reactions of fluorocytosine production process

Reaction thermal runaway is one of the most important reasons leading to chemical accidents. With the rapid development of the chemical industry in the world, especially the fine chemical industry, various safety accidents also occur frequently. Therefore, it is necessary to study the exothermic behavior of the reaction process. In this study, reaction calorimeter was used to study the exothermic phenomena during the chlorination reaction and amination reaction. Differential scanning calorimetry was performed on the reactants, and thermogravimetric experiments were performed on the products. In addition, adiabatic experiment was performed to study the thermal runaway behavior of amination products under adiabatic conditions. The results showed that the target reactions generated a large amount of heat in the initial stage. The maximum temperature of amination reaction is higher than the initial decomposition temperature of the amination product under adiabatic condition. The pyrolysis of amination product was divided into three stages. The product had a high apparent activation energy at the beginning of decomposition, and the apparent activation energy decreased as the decomposition progressed.     

Inherent thermal runaway hazard evaluation method of chemical process based on fire and explosion index

Thermal runaway hazard assessment provides the basis for comparing the hazard levels of different chemical processes. To make an overall evaluation, hazard of materials and reactions should be considered. However, most existing methods didn't take the both into account simultaneously, which may lead the assessment to a deviation from the actual hazard. Therefore, an integrated approach called Inherent Thermal-runaway Hazard Index (ITHI) was developed in this paper. Similar to Dow Fire and Explosion Index(F&EI) function, thermal runaway hazard of chemical process in ITHI was the product of material factor (MF) and risk index (RI) of reaction. MF was an indicator of material thermal hazards, which can be determined by initial reaction temperature and maximum power density. RI, which was the product of probability and severity, indicated the risk of thermal runaway during the reaction stage. Time to maximum rate under adiabatic conditions and criticality classes of scenario were used to indicate the runaway probability of the chemical process. Adiabatic temperature rise and heat of the desired reaction and secondary reaction were used to determine the severity of runaway reaction. Finally, predefined hazard classification criteria was used to classify and interpret the results obtained by this method. Moreover, the method was validated by case studies.     

Effect of pyrolysis and oxidation characteristics on lauric acid and stearic acid dust explosion hazards

The effect of pyrolysis and oxidation characteristics on the explosion sensitivity and severity parameters, including the minimum ignition energy MIE, minimum ignition temperature MIT, minimum explosion concentration MEC, maximum explosion pressure P_max, maximum rate of pressure rise (dP/dt)_max and deflagration index K_st, of lauric acid and stearic acid dust clouds was experimentally investigated. A synchronous thermal analyser was used to test the particle thermal characteristics. The functional test apparatuses including the 1.2 L Hartmann-tube apparatus, modified Godbert-Greenwald furnace, and 20 L explosion apparatus were used to test the explosion parameters. The results indicated that the rapid and slow weight loss processes of lauric acid dust followed a one-dimensional diffusion model (D1 model) and a 1.5 order chemical reaction model (F1.5 model), respectively. In addition, the rapid and slow weight loss processes of stearic acid followed a 1.5 order chemical reaction model (F1.5 model) and a three-dimensional diffusion model (D3 model), respectively, and the corresponding average apparent activation energy E and pre-exponential factor A were larger than those of lauric acid. The stearic acid dust explosion had higher values of MIE and MIT, which were mainly dependent on the higher pyrolysis and oxidation temperatures and the larger apparent activation energy E determining the slower rate of chemical bond breakage during pyrolysis and oxidation. In contrast, the lauric acid dust explosion had a higher MEC related to a smaller pre-exponential factor A with a lower amount of released reaction heat and a lower heat release rate during pyrolysis and oxidation. Additionally, due to the competition regime of the higher oxidation reaction heat release and greater consumption of oxygen during explosion, the explosion pressure P_m of the stearic acid dust was larger in low concentration ranges and decayed to an even smaller pressure than with lauric acid when the concentration exceeded 500 g/m³. The rate of explosion pressure rise (dP/dt)_m of the stearic acid dust was always larger in the experimental concentration range. The stearic acid dust explosion possessed a higher P_max, (dP/dt)_max and K_st mainly because of a larger pre-exponential factor A related to more active sites participating in the pyrolysis and oxidation reaction. Consequently, the active chemical reaction occurred more violently, and the temperature and overpressure rose faster, indicating a higher explosion hazard class for stearic acid dust.     

两种有机锌络合物处理棉花的霉变及热解行为研究

棉花是纺织业的重要原料,是人民群众生活不可或缺的必需品,同时也是我国进出口重要的商品。研究如何安全有效地进行棉花的储备具有十分重要的现实意义。棉纤维本身含有脂肪、蜡质和果胶等适合微生物生长繁殖的营养物质。在棉花储备中,高的回潮率会加速微生物的繁殖,进而产生热量。热量的累积会引起温度升高以及棉花霉变,不利于棉花的安全有效储存。因此,通过静电吸附法将安全无毒的有机锌络合物附着在棉纤维表面,研究表明,相同条件下,处理棉的霉变状况明显得到抑制。加速发霉条件下,未处理棉的相对于白纸的平均色差值为28.10,而双乙酸锌以及苯甲酸锌防霉处理棉的色差值分别为5.16和5.86,下降了81.6%和79.1%。自然发霉条件下,双乙酸锌以及苯甲酸锌防霉处理棉的色差值分别下降了53.8%和50.7%。同时研究了纯棉以及处理棉氮气下的热分解动力学,相比于未处理棉,双乙酸锌防霉处理后活化能下降了15.8%,而苯甲酸锌防霉处理后活化能下降了10.9%。此外,利用实时红外和热重红外联用技术得到了样品在热解过程中固相以及气相的裂解产物的红外谱图,发现防霉处理能一定程度上抑制棉花热解。